![]() ![]() Last but not least, attach the holder onto the wall with screws and hang the key chains in the slots!īefore You Go! If you’re a maker who’s into power tools, you have to know about Maker Days. Repeat steps 1-6 with remaining geo keychains. Attach Keys: Slip the key into the jump or split ring. Attach Jump Rings: At the opposite ends of the cording, attach a jump ring (or a more traditional split ring) by tying it right into the double knot.Ħ. Attach Wire Cording: Bend the sides of the cage back together and double knot together with a 9″ piece of leather cording.ĥ. Remove the Bling: Gently bend back the split sides of the cage, and remove the crystal.Ĥ. Open up the Geo Cage: Look for a weakly welded connection on the cage and carefully split the connection with a wire cutters.ģ. Use a needle nose pliers to split the jump rings and take them off.Ģ. I liked the modern look of the cages without the bling and chose to remove them. Remove the Jump Rings: The caged necklace pendants will arrive with a giant crystal in the middle of them. For the 2 interior slots, you’ll need to approach the slots from each side as opposed to completely straight on.ġ. Tip: When making the key chain slots with the cutting wheel, it’s helpful to make several passes back and forth across the surface to create the slot. Cut Key Chain Slots: With the Micro’s cutting wheel attachment, create 3/8″ – 1/2″ deep slots for the key chains.Mark Key Chain Slots: Evenly space the 4 slots across the front of the holder.Attach Keyhole Hangers: Screw in keyhole hangers using a simple screwdriver or cordless drill (depending on wood hardness).Smooth the rough routed surface with the same Micro sanding discs used in step 1. Then rout an additional 1/8″ recess only in the location where the screw head will enter the keyhole hanger. Rout Recesses for Keyhole Hangers: Use the Micro’s engraving cutter to rout out an 1/8″ recess following the pencil outline created in step 2.Mark for Keyhole Hangers: Determine what will be the front & back of the holder, and trace around the keyhole hangers on the back side.Next switch to a medium grade disc and then to a fine grade disc until completely smooth. In a smooth continuous motion, move the sanding disc over the surface of the wood removing any rough splinters on the surface. Attach a coarse grade sanding disc onto the EZ Drum Mandrel and lock it into place on the rotary tool. Sand the 1×2 Board: Depending on the cut of wood, you’ll likely need to start with one of the coarse grade sanding discs and work your way to the finest one.Note: While you’re gathering materials, make sure your Micro is on the charger (or already charged). 4 Caged necklace pendants (I picked these up at Michael’s, and it looks like they’re only available in stores.).No more frantic key searching for this gal! If you too need to organize your home’s key situation, check out the modern key holder solution I made for my entry. ![]() ![]() Normally making a wall-mounted key holder with key chain slots & recessed keyhole hangers would require 3 big-daddy tools: belt sander, mitre saw and router, but instead I’m simplifying things and using the Dremel 8050 Micro, a handheld rotary tool that satisfies all 3 tool needs in one. Key Storage in the Entry.īecause our entry is a small space, I knew the key holder had to be wall mounted, and I found inspiration in this only-sold-in-Danish-stores key holder. So when Dremel challenged me to share a small space solution as part of their month-long August Maker Days (more on this in a bit!), it was a no-brainer which area to tackle. And it makes for a frantic struggle when you need to dash out the door in a hurry. Without a designated drop spot for them when you walk in the front door, our keys often end up in scattered, hard to find places throughout the home. Not only are we looking after our own home and car keys but the duplex’s exterior door key, our tenant’s spare keys, etc. As owners of a Duplex home, it’s safe to say we have a healthy number of keys to manage.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |